Planning a change to your factory’s production boundaries? Review AFVA’s BRCGS consulting support or contact AFVA for free initial guidance.
A BRCGS production risk zone review needs the product and process facts behind a factory layout. Moving a line, doorway or staff entrance can alter how a boundary works even when the product recipe stays the same. Review that question while design choices are still open.
This guide helps New Zealand manufacturers prepare a focused review brief. It does not classify a site as high-risk, high-care or ambient high-care, reproduce the standard’s definitions, or provide an engineering design. For broader certification preparation, use AFVA’s BRCGS gap-assessment guide.
Quick answer. Record the products and processing covered, locate relevant pathogen-control steps, and compare current and proposed movement across production boundaries. Gather the evidence behind the existing zone assessment and identify what the layout change could affect. Have the applicable assessment and control questions resolved against the current authorised BRCGS requirements before accepting the final design or relying on the changed arrangement.
Keep production risk zone classification tied to the product
The official BRCGS Food Safety Issue 9 self-assessment tool requires a site assessment using the standard’s production risk zone definitions. It distinguishes high-risk, high-care and ambient high-care arrangements; they are not interchangeable labels for a clean room.
Use the applicable authorised standard and technical guidance for the actual classification. A room name, floor colour or a statement that the product is ready-to-eat cannot settle the complete assessment here. Keep the technical reasoning and its source identifiable.
Prepare a product/process summary before the layout discussion. Include intended use, relevant treatment, subsequent handling, storage and packaging, with references to the supporting specifications and food safety study. Mark missing information rather than choosing a zone to fit a preferred building plan.
Describe the change as three connected questions
A reviewer needs to understand what is different and why it matters. Prepare a clear current plan and a separate proposed version. Identify the change boundary, rather than replacing the current drawing so nobody can reconstruct the comparison. The following brief structure is AFVA’s recommendation, not a substitute zoning decision tree.
A focused layout-review brief
Review question
What is changing?
Provide
Current and proposed room use, equipment position, access and movement.
Decision needed
Which existing assumptions and boundaries require reassessment?
Review question
What product evidence applies?
Provide
Product/process scope, relevant control steps and the existing documented zone rationale.
Decision needed
Does that rationale still fit the proposed arrangement?
Review question
What will demonstrate implementation?
Provide
Affected procedures, training, checks and responsibilities, with evidence gaps.
Decision needed
What must be completed and reviewed before the changed operation is used?
Trace movement across the proposed boundary
Walk each relevant route through the proposed arrangement. Consider materials, product, packaging, people, equipment, rework and waste, including occasional activities. A route used only during maintenance or a difficult changeover can still matter.
BRCGS’s official tool links zone assessment to the site map and movement routes. Its production-zone section also addresses relevant segregation and contamination-control arrangements, with different provisions applying to different zone types. Use the full criteria for the actual classification rather than transferring a solution from another area.
As a preparation exercise, ask the people doing the work to describe a normal shift and an awkward shift. Where does a trolley wait? How does a maintenance item return? What happens when a usual route is unavailable? Record these as review questions with their source, not as untested assurances that the design is suitable.
Include relevant air, drainage and utility information for competent technical review. A floor plan alone may not explain those connections. The appropriate specialists should assess the design evidence; this article does not supply airflow values, pressure settings or drainage specifications.
Connect the design to the food safety system
List the procedures and assumptions that rely on the current layout. Identify the likely owners of each update, such as production, engineering, hygiene and quality. Work through the dependencies together so a drawing revision does not arrive after staff instructions have already been issued.
The Codex General Principles of Food Hygiene supports reviewing the HACCP system when a change may affect food safety, with revalidation where necessary. Codex is technical guidance; it does not determine a BRCGS zone classification or replace the relevant New Zealand programme requirements.
Ask whether supporting evidence still covers the proposed conditions. AFVA’s HACCP validation evidence-file guide can help organise that evidence. Keep an unresolved applicability question open until the competent reviewer has addressed it. A historic satisfactory result for the old arrangement does not automatically demonstrate the new one.
Agree review responsibilities before the design is fixed
Nominate who coordinates the review, who supplies technical information and who can authorise each project decision. Distinguish the consultant’s findings, an engineer’s design work, the operator’s implementation decision and the certification body’s certification role.
Bring unresolved standard-interpretation or audit-scope questions to the appropriate certification body early enough to obtain a clear response. Check any required notifications through your actual certification agreement and applicable protocol. A consultant’s completed brief does not itself alter certification scope or guarantee that a design will be accepted.
Record conditions attached to a review. For example, a conclusion may depend on a material transfer happening by a specified route. If the project later removes that arrangement, return the change to review instead of carrying forward the earlier conclusion unchanged.
Use a readiness checklist for the project handover
- The product and process scope is clear and the zone rationale can be located.
- Current and proposed plans are separately identified and dated.
- Relevant control steps and movement routes are visible.
- Routine and occasional boundary crossings have been discussed with staff.
- Air, drainage, utilities and other specialist questions have appropriate owners.
- Affected procedures, staff instructions and evidence needs are listed.
- Review conclusions, assumptions and open actions remain traceable.
- The handover identifies who checks the implemented arrangement and records the outcome.
These are recommended preparation fields, not a complete certification checklist. Inspect the installed arrangement against the reviewed design and resolve differences. A contractor’s statement that construction is complete does not demonstrate every food safety condition has been implemented.
Avoid a zoning decision based on a drawing alone
Common problems include selecting a zone name before collecting product facts, assuming every zone type needs identical controls, examining only normal production and overlooking occasional movement. Another is treating a signed drawing as the entire review while the operating instructions still describe the old layout.
Keep your criteria current. BRCGS’s current Food Safety page explains that position statements are binding extensions of its standard. Check the applicable standard, relevant statements and certification-body arrangements for the planned review date. The official position-statement list provides the current documents.
AFVA provides consulting and readiness support within an agreed scope. Describe the bounded question you need help with, and identify engineering, microbiological or other specialist work separately. AFVA does not issue BRCGS certification or promise a certification grade.
Frequently asked questions
Does every ready-to-eat product need the same zone?
Do not classify from that description alone. Apply the full relevant product/process definitions and assessment in the authorised standard and guidance, with competent review of the actual operation.
Are high-risk, high-care and ambient high-care interchangeable?
No. The standard distinguishes these production risk zones. Establish the applicable classification and controls for the actual products and processes; a generic clean-room description is insufficient.
Can we keep the current zone name when moving a packing line?
Review the effect before assuming that the existing rationale remains applicable. The change may affect product exposure, movement or supporting controls even if the recipe is unchanged.
Is a site map enough for the review?
It is important evidence, but the reviewer also needs product/process facts, the zone rationale and relevant operating information. Specialist system details may be needed beyond what a floor plan shows.
Will AFVA approve the factory design for BRCGS certification?
AFVA can provide agreed consulting and preparation support. Technical design responsibilities and the certification body’s assessment remain separate. Agree the review scope, specialist needs and outputs before relying on its conclusions.
How AFVA can help
Prepare the existing zone assessment, current and proposed plans, product/process summary and a short list of unresolved boundary questions. Ask AFVA about a focused BRCGS preparation review so the next work is defined before the layout is fixed.
General information only. Confirm the requirements that apply to your specific food activities, products, processes, locations and sales model.
Need Practical Food Safety Support for Your Business?
Contact us for free initial guidance. We provide practical, plain-English food safety support for New Zealand food businesses across all service areas.
This article provides general information only and is not a substitute for professional advice specific to your situation. Contact us for guidance based on your actual food activities and requirements.